Installing a New Shower Unit
An effective shower installation needs careful preparation and a lot of work. For the most part, you will require to do 3 kinds of tasks: framing walls, setting up the plumbing, and finishing walls.
Preparation
Firstly, you need to pick the kind of shower that you wish to set up. It is very important to establish whether the picked shower can handling particular systems and can manage a safe level of water through the boiler. Most shower units nowadays are created to be flexible to various water pressures (such as stored hot water and cold mains).
It is also important to take into consideration the water pressure and the preparation of the piping and drain for the shower
Different https://www.fixitrightplumbing.com.au/plumber-armadale/ Kinds of Shower Units
Push-on Mixer: The pipe and spray parts of the push-on mixer shower unit can be linked to the bath tap according to your requirement, and the water temperature level can be changed via the taps. Push-on mixers are inexpensive and extremely simple to install. Nevertheless, although the hose pipe connection is basic, it is easily dislodged. Additionally, it is troublesome to change the temperature level.
Bath/ Shower Mixer: The tube and spray of this type of shower are combined with a bath mixer tap, and the temperature can be changed through the bath taps. It is a very low-cost alternative and no additional plumbing is involved. Nevertheless, the bath/shower mixers likewise experience bothersome temperature control options.
Manual Mixer: The tube and spray of a manual mixer shower unit are a part of the wall system and the hot and cold water supplies are linked to a single valve The temperature level and pressure of the water are managed through either one or a variety of knobs (in more expensive showers). Although temperature control is a lot easier in manual mixer types, they are more pricey than the previously mentioned mixers. They likewise need additional plumbing of hot and cold supply of water pipes.
Thermostatic Mixer: The tube and spray of this shower type are a part of the wall system and the hot and cold water materials are linked to a single valve here too. It is complete with a built-in stabiliser to self-adjust the water temperature level and to avoid it from ending up being too hot. Among the biggest benefits of a thermostatic mixer shower type consists of convenient temperature control. Nevertheless, it is the most pricey of the different mixer alternatives.
Power Shower: A power shower is a single unit including an effective electric pump that is capable of modifying both the water pressure and temperature. This kind of shower can be fitted if there is water supply from a cold water cistern and a hot water cylinder. A power shower makes the adjustment of both pressure and temperature level simple. On the other hand, it disagrees for water heated up directly by the shower or where the water is provided by a combination boiler under mains pressure.
Electric Shower: An electrical shower is plumbed into a mains cold water supply and it heats the water electrically. It is very important to keep in mind that for this shower type to be installed, the mains pressure needs to be at least 0.7 kg/sq cm (10lb/sq in). The system permits the temperature level and pressure to be changed through a knob. Models with temperature stabilisers are much better as they stay untouched by other taps somewhere else in usage within the household. A major drawback of electrical showers is that the control knob only enables the choice of high temperatures at less pressure, or lower temperature levels at a greater pressure. This is bothersome in the winter when the spray is frequently weak and the mains water is chillier. However, this issue is taken on in some designs which are available with a winter/summer setting.
Method
Depending on the type of shower you wish to install, the shower head must either be fitted in order to prevent its contact with the water in the bath below or the base tray, or it should have a check valve.
Use the instruction guide offered with the shower system to fit the shower control.
Before fitting the pipelines that will supply the water to the shower system, it is very important to cut off the supply of water. In order to protect the pipes, they ought to be provided a water resistant covering and also fitted with isolating valves. The pipelines can then be buried into the wall and plastered over to neaten the general look.
Fit Fix-It Right Plumbing the base tray, shower head, and fittings.
Connect the main shower control to the pipes that will be providing the water (This may need a female screw thread adapter).
Reconnect the water system and test the pipelines for any leaks, as some may require tightening.
If you are installing an electrical shower, remember to switch off the electrical energy supply before making any electrical connections. As soon as these connections have actually been made (there should be guidance within the user's manual), the power supply can be switched back on.
Adjusting Water Pressure to Fit Your Shower
The cold water tank can be lifted to a greater height (often as little as 150mm (6inches)) by fitting a strong wood support beneath it-- possibly composed of struts and blockboards. If you choose this alternative, the main and circulation pipes will likewise need to be raised to meet the brand-new height of the reservoir.
Alternatively, a booster pump (a single pump or a dual/twin pump) can be fitted. Whichever type is picked, it needs to be linked into the power supply in order to operate.
Piping and Drainage
It is best to utilize 15mm diameter supply pipes, and make the go to the shower as brief and straight as possible so regarding maintain maximum pressure and reduce heat loss. In addition, by minimising making use of elbows for pipeline corners, you can decrease the resistance in the flow of the water supply. You can attain this by bending the pipes instead.
Most Common Mistakes
# Breaking or neglecting local code restrictions.
# Utilizing pipes that are too small.
# Attaching copper to galvanized without using a brass or dielectric fitting between the two.
# Not utilizing tape or pipeline compound at threaded joints.
# Not leveling your fixtures when installing them.
# Not installing an air gap filling for fixtures.
# Cutting supply stub outs too short to set up the shutoff valves onto after the completed wall is in place.
# Not properly aligning tubing into fittings or stop valves. (Forcing the nut onto the compression ring at an angle when the tubing is at an angle will cause a leakage.)
# When turning the water back on in your home, constantly run the outside pipe valve or flush your toilets to bleed dirt and air from the lines. This debris can trigger issues in your sink faucets and other pipes trim.